Dolls obtaining a teenage women obtaining a large sweater along with a skateboarding teenage boy in shorts might be created with miniature brooms. The broomstraws complete could be the dolls hair. Complete instructions receive. what size skateboard should i get 

(Note: Use thick craft glue helping you to connect felt and construction paper pieces together. Use glue gun for other things Use photo being an setup guide. Squeeze little bit of paint onto paper plate if needed. Let paint dry before proceeding to a different color.

For mind, use flat paintbrush to color front and side edges of wooden spoon with flesh let dry. For every eye, dip handle finish of paintbrush into black paint touch brush handle to wide finish of spoon. Use liner brush and black paint to color nose, mouth, and eyebrows. For cheekbones, mix neon pink with which makes it. neon pink paint cheekbones. Let dry.

To create figure, see Fig. 1. Place broom, bristles up, on work surface. For arms, center and glue 7" period of chenille stem to back of broom where broom bristles . Bend arms around both sides of broom glue arms to sides of broom to secure.

For body, utilize a generous volume of glue helping you to connect body to front of broom handle, covering center of arms.

For legs, use sandpaper or file to slightly flatten one finish of each and every craft stick. Glue one craft stick, rounded complete, to left side of body on the top of broom handle to make certain the the very best leg is despite bottom of body. Making certain bottom of legs are, glue right leg to back of broom handle very similar.

For every skate, glue one oblong to bottom of each and every leg to make sure that flat part of leg reaches one finish of skate and toes point forward. Paint legs and skates with black.

Cut sweater, headband, and boom box patterns from Pattern Section, cutting along dashed lines for boom box. Use sweater and headband patterns to lessen materials as indicated. Set boom box pattern aside.

Using sweater pattern just like a guide, use black marker to draw in wavy lines at finish of each and every sleeve and along hem line on sweater back and front. Place one sweater piece, right side lower, on work surface. Spread an sufficient volume of glue on back of broom handle center handle on sweater back and press in position. Position arms to make sure that arm is centered along period of each sleeve glue arms to center of sleeves. Departing hem, neck, and bottom of sleeves open, glue outdoors edges of sweater front to sweater back.

For every hands, bend finish of each and every chenille arm upward use wire cutters to trim excess stem, departing singleOr4" extended hands extending beyond side of sleeve. Use neon pink to color a wavy line across neckline also to paint three buttons, evenly spaced, lower center front of sweater.

For wheels, paint front, back, and edges of each and every wooden circle with neon pink. For wheel hub, use black to color a united states .in center of each and every wheel somewhere let dry. With wheel hubs out, vertically glue some wheels to bottom front of just one skate another volume of wheels to bottom back of skate. Repeat for second skate. how to set up a skateboard 

For hair, cut several bristles from back of mind. With bottom edges even, glue bristles vertically across top front of mind trim ends if needed. Glue headband inside the the very best mind to make certain topping side of headband is despite bottom of bristles. Use neon pink to color a wavy horizontal line across bottom and top edges of headband.

For hair bows, cut neon eco-friendly ribbon into two 5" lengths. Gather somewhat bundle of bristles together at left side of hair. Wrap ribbon around bundle tie ribbon results in a 2-loop bow with 1/2" loops and 1/2" tails. Cut ribbon creates a slant. Repeat for opposite side of hair.

For boom box, use pattern to lessen two boom box pieces making use of this. pink construction paper set one piece aside for back. For loudspeakers, use boom box pattern as helpful approach to trace one speaker onto tracing paper. Eliminate circle. Use speaker pattern to lessen two loudspeakers from black construction paper. Use thick craft glue helping you to connect loudspeakers, evenly spaced, across front of boom box. Using pattern just like a guide and black marker, draw buttons, tuner, and tape cassette onto boom box.

For necklace, string beads on remaining 10" period of string or floss. Wrap necklace around neck and tie ends together inside the overhand knot.

Skateboard Mike

For mind and legs, paint front and side edges of spoon and front, back, and side edges of ordinary craft sticks with flesh let dry. For cheekbones, mix some neon, which makes it. neon orange paint cheekbones. For mouth, use black to color a curved mouth centered below cheekbones.

Working very similar as Rosie: glue mind, arms, and legs to body for foot, glue one wooden oblong to bottom of each and every leg, except have both foot slightly pointing to left.

Cut shirt, shorts, shoe, skateboard, shades, and headband patterns from Pattern Section use patterns to lessen materials as indicated. Set skateboard pattern aside. Very similar as Rosie's sweater, glue shorts to bottom of body and shirt to top. Shape arms as preferred. Cut bristles from back of broom and canopy the most effective mind very similar as Rosie. Glue headband inside the the very best mind. Glue shades below headband.

Use neon orange to color the next: two diagonal stripes on right leg of shorts a horizontal wavy line across headband and dots on shirt front. Let dry. Turn figure over. Use neon orange to color dots on back of blouse let dry.

To color footwear, use pattern just like a guide. To begin with shoe, place two shoe pieces flat on work surface with toes together. Paint large circles and eyelets with neon pink. For shoelaces, use black to color a vertical wavy line lower both sides of shoe. Repeat for second shoe. Let dry. Helping you to connect footwear to foot, see Fig. 2. With colored sides facing out, place two shoe pieces together around bottom of leg. Glue shoe pieces together at back and front edges, departing top front of shoe slightly open.

For skateboard, place skateboard pattern on jumbo craft stay with rounded finish of pattern matching rounded finish of craft stick. Use pencil to draw in a line across craft stick at straight finish of pattern. Use saw or utility knife to lessen rounded finish from stick. Sand or file cut edge smooth.

Paint front, back, and sides of skateboard. Using pattern just like a guide, paint a eco-friendly, pink, and orange stripe diagonally across front and sides of board. how to turn on a skateboard 

For wheels, paint wooden circles with black. For wheel hubs, paint circle in center of each and every wheel somewhere with neon orange. With wheel hubs out, vertically glue some wheels to bottom front of skateboard to make sure that wheels are 5/8", apart and front edges of wheels are 1/2" from rounded side of skateboard. Very similar, glue another volume of wheels to back of skateboard to make sure that back edges of wheels are 5/8" apart and " from back side of skateboard. Paint over any uncovered glue with appropriate shade of paint let dry.

With many different glue, center and glue figure to skateboard.

You do not need loops. If you use the File Trigger the Job will run once for each file. Then you use the Variables created in runtime from the File trigger in upcoming Tasks. Please check the File Trigger tutorial here: http://www.visualcron.com/tutorials.aspx 

---